The 2nd Annual Conference of the Japanese Institute of Additive Manufacturing
Advanced Search

Session Details

Poster Session

[P-A]Poster Session

Thu. Sep 3, 2026 1:00 PM - 2:30 PM JST
Thu. Sep 3, 2026 4:00 AM - 5:30 AM UTC
Conference Room A

[P-A-01]Development of a 316L Stainless Steel Self-catalytic Reactor by Metal 3D Additive Manufacturing and Selectivity Control in CO2 Hydrogenation

*Ririko Aoyama1, Hyo-Jin Kim1, Takayoshi Nakano1, Kohsuke Mori1 (1. The University of Osaka)
Comment()

[P-A-02]Development of PdAg-supported AM Reactor
for CO2 Resource Conversion

*Naoyuki Hayashida1, Hyo-Jin Kim1, Takayoshi Nakano1, Kohsuke Mori1 (1. The University of Osaka)
Comment()

[P-A-03]Self-Optimization of CO2 Conversion via Dynamic Surface Reconstruction in Additively Manufactured Cantor High-Entropy Alloy Catalysts

*JEONGMIN CHOI1, HYOJIN KIM1, Takayoshi Nakano1, Kohsuke Mori1 (1. The University of Osaka)
Comment()

[P-A-04]Microstructural Control of Oxygen-added β-containing TiAl Alloys Fabricated by Additive Manufacturing

*Yuya Watanabe1, Ken Cho1, Masao Takeyama2, Takayoshi Nakano1, Hiroyuki Yasuda1 (1. The University of Osaka, 2. Institute of Science Tokyo)
Comment()

[P-A-05]Investigation of Deformation Mechanism in Ni-based Superalloy
Fabricated by Metal Additive Manufacturing Using in-situ EBSD

*Shunya Maruo1, Kippei Yamashita1, Cho Ken1, Tsuyoshi Mayama2, Takayoshi Nakano1, Hiroyuki Yasuda1 (1. The University of Osaka, 2. Kumamoto University)
Comment()

[P-A-06]Evaluation of Crack Susceptibility of Ni-base Single Crystal Superalloys by Single-track Laser Melting

*Takashi Suzuki1,3,4, Masahiro Kusano3, Satoshi Utada3, Kosuke Kuwabara3, Kyoko Kawagishi3, Makoto Watanabe3, Toshio Osada2,3 (1. Yokohama National University D2, 2. Yokohama National University, 3. National Institute for Materials Science, 4. Nagano Prefecture General Industrial Technology Center)
Comment()

[P-A-07]Effect of wire surface condition on the properties of additively manufactured pure iron as soft magnetic materials

*Shota iimura1, Gaoge Xue2 (1. Kobe Steel Ltd., 2. KOBELCO WIRE COMPANY, LTD.)
Comment()

[P-A-08]Powder Design for Enhanced Sinterability in Indirect Ceramic Additive Manufacturing

*Nagisa Murakami1, Yuki Kuwano1, Kian Wai Tan1, Go Kawamura1, Atsunori Matsuda1, Hiroyuki Muto1 (1. Toyohashi University of Technology)
Comment()

[P-A-09]Design of plant prickles biomimetic micro-protrusion for metals and CFRTP easily disassemblable joining

Ryuma Ohnishi1, *Kiyokazu Yasuda1, Tai Wang1 (1. The University of Osaka)
Comment()

[P-A-10]Development of a Knee Orthosis Structurally Designed with FDM-Fabricated Carbon Fiber-Reinforced Plastic Components

*Ririko Matsumoto1, Noriyuki Hisamori2 (1. Sophia University Graduate School, 2. Sophia University Faculty of Science and Technology)
Comment()

[P-A-11]Establishment of Percutaneous Transhepatic Cholangial Drainage Training Model with AdditiveManufacturing

*Risa Terada1, Wakabayashi Yuki1, Sara Watanabe1, Takayoshi Suzuki2, Takeshi Soyama3, Taku Maeda1, Kuroshima Shinichiro1 (1. Hokkaido University Hospital, 2. Fujita Health University Hospital, 3. Kushiro City General Hospital)
Comment()

[P-A-12]Understanding the anatomical structure using a 3D model of an extremely long-lived naked mole-rats

*TETSUYA ADACHI1, Keiji Adachi1, Fumishige Oseko1 (1. Kyoto Prefectural University of Medicine)
Comment()

[P-A-13]An Integrated Digital Workflow for Mandibular Marginal Resection and
the Challenges of Additive Manufacturing in Dentistry

*KIMIYA OZAKI1, Mariko Ota1, Yu Nakai2, Masayuki Shinohara2, Ken-ichiro Sakata2, Risa Terada3, Sara Watanabe3, Yuki Wakabayashi3, Shinichiro Kuroshima4, Yutaka Watanabe1, Taku Maeda5 (1. Gerodontology, Hokkaido University, 2. Oral Diagnosis and Medicine, Hokkaido University, 3. Department of Dental Medical Laboratory, Hokkaido University Hospital, 4. Fixed and Regenerative Prosthodontics, Hokkaido University, 5. Department of Plastic and Reconstructive Surgery, Faculty of Medicine and Graduate School of Medicine, Hokkaido University)
Comment()

[P-A-14]Antimicrobial control via osteoblast alignment guided by additively manufactured Ti-6Al-4V

*Tian Liu1, Tadaaki Matsuzaka1, Aira Matsugaki1, Takayoshi Nakano1 (1. the University of Osaka)
Comment()

[P-A-15]Improvement of Fatigue Strength of Ti-6Al-4V Alloy Fabricated by Selective Laser Melting via a Multi-Composite Surface Modification Process

*Mizuki Kogane1, Noriyuki Hisamori2, Amiru Takahashi3, Hiroyuki Takahashi3, Yusei Iida4, Masahiro Tsukahara4, Yuji Kobayashi5 (1. Graduate School of Sophia Univ., 2. Sophia Univ., 3. Nakashima Healthforce Co., Ltd., 4. Neturen Co., Ltd., 5. SINTOKOGIO, LTD.)
Comment()

[P-A-16]Crystallographic Texture Control in Additive Manufacturing
of Tantalum for Biomedical Applications

*NUR ZULAIKHA BINTI MOHAMAD ZAIDI1, Ozkan Gokcekaya1, Takayoshi Nakano1 (1. UNIVERSITY OF OSAKA)
Comment()

[P-A-17]Elastic Properties in Ti-Cr Alloys Prepared by L-PBF

*Tomohiro Minemoto1, Ryosuke Ozasa1, Takuya Ishimoto1,2, Takayoshi Nakano1, Masakazu Tane1 (1. The University of Osaka, 2. University of Toyama)
Comment()

[P-A-18]Effect of Heat Treatment on the Mechanical Properties of CCM Alloy Fabricated by Selective Laser Melting

*Akari Deto1, Noriyuki Hisamori2, Amiru Takahashi3, Hiroyuki Takahashi3, Yuji Kobayashi4 (1. Graduate School of Sophia University, 2. Sophia University, 3. NAKASHIMA HEALTHFORCE CO., LTD., 4. SINTOKOGIO, LTD.)
Comment()

[P-A-19]Depowdering of Complex-Shaped AM AlSi10Mg by Chemical Polishing

*Shinya Tako1, Toshiaki Uematsu1, Masahiro Nakayama2 (1. Industrial Research Institute of Shizuoka Prefecture, Hamamatsu, 2. Nakayama Precious Metal Plating Co., Ltd.)
Comment()

[P-A-20]Additive Manufacturing of Ti-6Al-4V by Wire-Laser DED with Wide-Area Local Shielding

*Yasutomo Tanihara1, Daiji Morita1, Yusuke Seguchi1 (1. Mitsubishi Electric)
Comment()
Back to Category List