[1-1A]Directed Energy Depositionof TiAl4822 and Repair of the Turbine Blade 《 Sintering 》
*Koji Kakehi1, Wataru Oishi1, Kenzo Sakata1, Kazuhiro Gokan2, Kazuhiro Mizuta2(1. Tokyo Metropolitan University, 2. AeroEdge Co., Ltd.)
Autumn Meeting of the Japan Society of Powder and Powder Metallurgy, 2024
Nov 19 - Nov 21, 2024TOKI MESSE, Niigata Convention Center
You can search for presentations in this event.
Search
Autumn Meeting of the Japan Society of Powder and Powder Metallurgy, 2024
Nov 19 - Nov 21, 2024TOKI MESSE, Niigata Convention Center
You can search for presentations in this event.
SearchSearch Results(155)
[1-2A]Microstructure and mechanical properties of DED IN718 after homogenization 《 Physical Property 》
*Nanae Sato1, Naidu Palleda1, Koji Kakehi1, Kazuhiro Gokan2(1. Tokyo Metropolitan University, 2. AeroEdge Co.,Ltd）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-3A]Fatigue properties of Alloy718 built by EB-PBF additive manufacturing 《 Physical Property 》
*Koki Ogawa1, Aoi Morishige1, Naidu Palleda1, Hasina Tabassum Chowdhury1, Koji Kakehi1, Ayumu Miyakita2, Kazuhiro Masuda2, Takashi Sato2(1. Tokyo Metropolitan University, 2. JEOL Ltd.）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-4A]Effect of Si content on the metallurgical structure of Alloy718 laminate molding body, a Ni-based super heat-resistant alloy 《 Physical Property, Evaluation Technology 》
*Naomi Kitagawa1, Yuki Matsushita1, Norihito Sakaguchi2, Genki Saito3, Kiyotaka Matsuura2(1. MITSUBISHI STEEL MFG. CO., LTD. , 2. Hokkaido University, 3. Nagoya University)
[1-5A]Additive manufacturing of water atomized SUS316L stainless steel powder and its corrosion resistance 《 Physical Property 》
Akihiro HIRAYAMA1, *Akira Otsu1, Akihiko YANAGITANI2, Takahiro KANEYOSHI1, Tohru YAMASAKI1(1. Hyogo Prefectural Institute of Technology, 2. Research Center for Advanced Metallic Materials, University of Hyogo)
[1-6A]Resistance of Oxidation at 800℃ of SUS316L fabricated by DED-type additive manufacturing 《 Physical Property 》
*Dai Shimazu1, Yen-Ling Kuo1, Makoto Nanko1(1. Nagaoka University of Technology）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-7A]Influence of anisotropy on gas nitriding of 18%Ni maraging steel components fabricated by additive manufacturing 《 Physical Property 》
*Nazuna IDETA1, Yen-Rin KUO1, Makoto NANKO1, Tsuyoshi SUGIMOTO2(1. Nagaoka University of Technology , 2. National Institute of Technology, Asahikawa College）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-8A]Development of Titanium Oxides-Coated 316L Stainless Steel via Laser Powder Bed Fusion for Biomedical Applications 《 Synthesis Process 》
*Xiao Wang1, Mingqi Dong1, Zhenxing Zhou1, Weiwei Zhou1, Naoyuki Nomura1(1. Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-9]Memorial Lecture of JSPM Award :
Fundamental Research and Development of Applied Technology on Metal Laser Additive Manufacturing 《 Evaluation Technology 》
*Hideki Kyogoku1(1. Kindai University)
[1-10]Memorial Lecture of JSPM Award :
Development of heat-resistant aluminum alloy utilizing rapid solidification characteristics of laser powder bed fusion 《 Physical Property 》
*Takahiro Kimura1(1. Osaka Research Institute of Industrial Science and Technology)
[1-11A]Effects of laser conditions and TiC coating thickness on the microstructure of TiC-coated carbon fiber/Al powder mixture after laser scanning 《 Synthesis Process, Physical Property 》
*Kazuki NAKAMURA1, Asuka SUZUKI1, Naoki TAKATA1, Makoto KOBASHI1(1. Nagoya university）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-12A]Preparation of a novel multiphase reinforced Al-matrix composite via laser powder bed fusion 《 Synthesis Process 》
*Li-Fu YI1, Weiwei ZHOU2, Taiki KOMORI1, Zhenxing ZHOU2, Naoyuki NOMURA2, Zhong-Chun CHEN1(1. Tottori University, 2. Tohoku University)
[1-13A]Improving Aluminum Powder Processability in Laser Additive Manufacturing via CuO Nanopowder Decoration 《 Synthesis Process, Physical Property 》
*Zhenxing ZHOU1, Weiwei Zhou1, Naoyuki Nomura1(1. Tohoku University)
[1-14A]Additive manufacturing of new Ti-Cu-O alloys with ultra-high strength and good ductility 《 Synthesis Process, Physical Property 》
*Peter MWANGI1, Yuto KURODA1, Kohei NAGAO1, Akira OTSU1,2, Tetsuhiko ONDA1, Takahiro KIMURA3, Takayuki NAKAMOTO3, Zhong-Chun CHEN1(1. Tottori University, 2. Hyogo Prefectural Institute of Technology, 3. Osaka Research Institute of Industrial Science and Technology）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-15A]Texture Refinement and Strengthening of Ti-6Al-4V LPBF Alloys by Controlling the Temperature and Atmosphere of Building Area 《 Physical Property 》
*Shota KARIYA1, Shota KUGIMIYA2, Takuma TERAMAE2, Jeff HUANG2, Ammarueda ISSARIYAPAT1, Junko UMEDA1, Kenta YAMANAKA3, Katsuyoshi KONDOH1(1. Joining and Welding Research Institute, Osaka University, 2. Graduate School of Engineering, Osaka University, 3. Institute for Materials Research, Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation. )
[1-16A]Effect of α’ phase decomposition on tensile properties of Ti-6Al-4V alloy prepared by Laser Powder Bed Fusion 《 Physical Property 》
*Reita Anan1, Shota Kariya2, Junko Umeda2, Katsuyoshi Kondoh2(1. Osaka University Graduate School of Engineering, Department of Mechanical Mngineering , 2. Joining and Welding Research institute Osaka University)
[1-17A]Uniformization of Mechanical Properties of Ti-6Al-4V Alloy by Controlling Pre-heating in Electron Beam Melting Process 《 Physical Property 》
Kota FUJIWARA1, *Takahiro KIMURA1(1. Osaka Reseach Institude of Industrial Science and Technology)
[1-18A]Effect of building conditions on the microstructure and plastic deformation behavior of Ti−6Al−4V alloys prepared by electron beam powder bed fusion 《 Physical Property, Evaluation Technology 》
*Kenta Yamanaka1, Manami Mori2, Yusuke Onuki3, Shota Kariya4, Katsuyoshi Kondo4, Shigeo Sato5, Akihiko Chiba1(1. Tohoku University, 2. National Institute of Technology, Sendai College, 3. Tokyo Denki University, 4. Osaka University, 5. Ibaraki University)
[1-19A]Exploration on β Stabilizing Elements of α+β Titanium Alloys for Promotion of Martensite Decomposition in Additive Manufacturing 《 Synthesis Process 》
*Takuma Teramae1, Ammarueda Issariyapat2, Shota Kariya2, Junko Umeda2, Katsuyoshi Kondoh2(1. Graduate School of Engineering, Osaka University, 2. Joining and Welding Research Institute, Osaka University）（※This presenter is a candidate for the Student Award for Outstanding Presentation. )
[1-20A]Microstructure Analysis of α+β Ti-2Mn Alloy Additively Manufactured with In Situ Martensite Decomposition 《 Synthesis Process 》
*Takuma Teramae1, Ammarueda Issariyapat2, Shota Kariya2, Jyunko Umeda2, Katsuyoshi Kondoh2(1. Graduate School of Engineering, Osaka University, 2. Joining and Welding Research Institute, Osaka University）（※This presenter is a candidate for the Student Award for Outstanding Presentation. )
[1-21A]Changes of cohesive strength and powder bed condition by adjusting the surface oxide layer of Ti-6Al-4V alloy powders for additive manufacturing 《 Physical Property, Evaluation Technology 》
*Naoki Kakegawa1, Weiwei Zhou1, Naoyuki Nomura1(1. Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation. )
[1-22A]Effect of material parameters on force-displacement curves in particle compression tests using FEM simulation 《 Evaluation Technology 》
*Shoma Sekita1, Zhang Tao1, Weiwei Zhou1, Naoyuki Nomura1(1. Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[1-23A]Microstructure and mechanical property of additive manufactured Nb alloy and Ta alloy 《 Sintering, Physical Property 》
*_ Suyalatu1, Kazuto Arakawa2, Hideki Wakabayashi2, Yasuko Ueda2, Norio Higuchi1, Hitoshi Sakai1, Yugo Higashida3, Masato Inata3(1. NTT DATA XAM Technologies Corporation, 2. Shimane University, 3. KIGUCHI TECHINCS inc.)
[2-1A]Stable local and electronic structures of Mg1+xV2-x-yMnyO4cathode materials for Mg secondary batteries after charging using first-principles calculations. 《 Physical Property, Computational Science 》
*Ryushi Imi1, Chiaki Ishibashi1, Yasushi Idemoto1, Naoto Kitamura1(1. Tokyo University of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-2A]Battery properties of Mg secondary battery cathode material 0.3MgCo2-xMnxO4-0.7Mg(Mg0.33V1.67-yNiy)O4 and composition dependence of crystal and electronic structures analysis for quantum beam 《 Synthesis Process, Physical Property 》
*Iroha Chida1, Yasushi Idemoto1, Chiaki Ishibashi1, Naoto Kitamura1(1. Tokyo university of science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-3A]Synthesis of Mg-Mn-Fe-O based cathode materials and their cathode properties and average and local structures 《 Physical Property 》
*Ryujin NAKAYAMA1, NAOTO KITAMURA1, CHIAKI ISHIBASHI1, YASUSHI IDEMOTO1(1. Tokyo University of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-4A]Investigation of the cathode properties and crystal structure of magnesium rechargeable battery cathode material Mg1+2xFe2-3xVxO4 《 Physical Property 》
Naoto Kitamura1, *Kazuma Koizumi1, Chiaki Ishibashi1, Yasushi Idemoto1(1. Tokyo University of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-5A]Battery characteristics and average/electronic structures of αMgCo2-xMnxO4-(1-α)Mg(Mg0.33V1.67-yNiy)O4 (α=0.5 x=0.6 y=0.1, 0.15) as a positive electrode for rechargeable magnesium batteries 《 Synthesis Process, Sintering, Evaluation Technology 》
Yasushi Idemoto1, *Aika Satou1, Chiaki Ishibashi1, Naoto Kitamura1(1. Tokyo University of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-6A]Local Structural Analysis and Substitution Effects of NASICON-Type Li1.5Al0.5-xMxGe1.5(PO4)3 (M=Substituent) Using First-Principles Calculations 《 Computational Science 》
CHIAKI ISHIBASHI1, *YIFEI DAI1, NAOTO KITAMURA1, YASUSHI IDEMOTO1(1. Tokyo University of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-7A]The relationship between ferroelectric properties and average, local, and electronic structures of (K,Na,Cu,Li)NbO3 《 Physical Property 》
*Genyu Yukimatsu1, Chiaki Ishibashi1, Naoto Kitamura1, Yasushi Idemoto1(1. Tokyo University of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-8A]Ferroelectric properties of Bi0.5K0.5TiO3-Bi(Fe1-xMx)O3-K(Nb0.5Ta0.5)O3-based ferroelectric, CuO addition and heat treatment effects on average and electronic structure 《 Synthesis Process, Sintering, Physical Property, Evaluation Technology 》
*Keitaro Sato1, Yasusi Idemoto1, Chiaki Ishibashi1, Naoto Kitamura1(1. Tokyo Univercity of Science）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-9A]Dependence of Strength Change of BaZrO3-Based Electrolytes with Hydration Treatment on Treatment Conditions 《 Physical Property 》
*Daiya Komine1, Shinya Kondou1, Takashi Teranishi1, Kishimoto Akira1(1. Okayama University）（※This presenter is a candidate for the Student Award for Outstanding Presentation. )
[2-10A]Preparation and microwave heating property of silica-carbon non-firing solidified composites 《 Synthesis Process 》
*Kento Ishii1, Gouki Miyawaki1, Yuuki Yoshida1, Masayoshi Fuji1(1. Nagoya Institute of Technology)
[2-11A]Fabrication and Characterization of Hydroxyapatite Water Purification Filter with Continuous Pore Structure Using Saccharide as Pore-forming Agent 《 Synthesis Process, Evaluation Technology 》
*Masako Uematsu1, Kent Ishii2, Megumi Ito3, Dalal Asker4, Benjamin D Hatton4, Teiichi Kimura1, Takamasa Ishigaki5, Tetsuo Uchikoshi3(1. Japan Fine Ceramics Center, 2. Nagoya Institute of Technology, 3. National Institute for Materials Science, 4. University of Toronto, 5. Hosei University)
[2-12A]Fabrication of InSb-CoSb3 sintered composite using a modified polyol process and evaluation of its thermoelectric properties 《 Synthesis Process, Physical Property 》
*Shigeru KATSUYAMA1, Yuza TANAKA1(1. Osaka University)
[2-13A]Synthesis and thermoelectric properties of misfit-layered cobalt oxides Ca3-xMxCo4O9 (M= Tb, Dy) 《 Synthesis Process, Physical Property 》
*Kotaro Kano1, Hiroto OHTA1, Masaki KATO1(1. Doshisha University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-14A]Physical Properties of Bi2-xEuxRu2-yTMyO7-δ(TM=transition metals)with Pyrochlore-type Structure 《 Synthesis Process, Physical Property 》
*KEISHO YORITAKA1, Hiroto OHTA1, Masaki KATO1(1. Doshisha University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-15A]Observation of Skutterudite thermoelectric material by photoemission electron microscopy 《 Physical Property, Evaluation Technology 》
*Takeshi SHIMADA1, Masashi FUJII1, Takuo Ohkochi2, Michiko MATSUDA1, Hayato NAKASAWA1, Takashi KAMIYA1(1. Proterial, 2. University of hyogo)
[2-16A]Synthesis of silicide thermoelectric materials using an ultra-high pressure SPS 《 Synthesis Process 》
*Yoshihisa Mori1, Daisuke Yamazaki2, Takio Hikono3, Daisuke Nakasa3(1. Okayama University of Science, 2. Okayama University, 3. NJS co. ltd.)
[2-17A]Thermoelectric properties of weak itinerant ferromagnetic Fe2V1-xTxAl1-ySiy (T = Cr, Fe) 《 Physical Property 》
*Naohito Tsujii1, Hiroya Sakurai1, Takao Mori1(1. National Institute for Materials Science)
[2-18A]Low-temperature synthesis of molybdenum nitrides using boron nitride as a nitrogen source 《 Synthesis Process 》
*Takahiro YAMADA1, Tenshin OSAKA1, Hisanori YAMANE1(1. Tohoku University)
[2-19B]Low-temperature synthesis of chromium nitride using chromium oxide and boron nitride 《 Synthesis Process 》
*Moto Kobayashi1, Akira Hosono1, Takahiro Yamada1(1. Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-20A]Production of MgMoO4 using the dissolution reaction of Mo and Mg/MgO 《 Synthesis Process 》
*Daisuke YAMAMICHI1, Daichi SASAKI1, Hiroyuki FUJIKI1(1. Muroran Institute of Technology）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-21A]Production of CaWO4 and SrWO4 Using Corrosion Reaction of Metal 《 Synthesis Process 》
*Risa ITO1, Daichi SASAKI1, Hiroyuki FUJIKI1(1. Muroran Institute of Technology）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[2-22A]Evaluation of Initial Film Formation and Growth During Aerosol Deposition 《 Synthesis Process, Physical Property 》
*Anna Ikehata1, Go Kawamura1, Atsunori Matsuda1, Naoyuki Fujita2, Hirofumi Minamoto3, Wai Kian Tan1, Hiroyuki Muto1(1. Toyohashi University of Technology, 2. The National Institute of Technology, 3. Shizuoka Institute of Science and Technology）（※This presenter is a candidate for the Student Award for Outstanding Presentation. )
[2-23B]The Process Parameter Investigation of Dynamic Balancing in Fine Powder Production Using the Plasma Rotating Electrode Process (PREP) 《 Physical Property 》
*Hao WANG1, Yujie Cui3, Jianwen Yang4, Takemi Chiba5, Tadashi Fujieda1, Kenta Yamanaka2, Akihiko Chiba6(1. Co-Creation Institute for Advanced Materials , Shimane University, 2. Institute for Materials Research, Tohoku University, 3. Beijing Advanced Innovation Center for Materials Genome Engineering, University of Science and Technology Beijing, 4. Shanxi Guizidan New Materials Co., Ltd, 5. Tohoku PREP Technology Co. Ltd, 6. New Industry Creation Hatchery Center (NICHe), Tohoku University)
[3-1A]DIC analysis of sintering deformation behavior in stepped powder compacts with inhomogeneous density distribution 《 Sintering 》
*Yamato Ikeda1, Kentaro Kudo2, Noriharu Yodoshi2, Kazunari Shinagawa2(1. Graduate School of Kyushu University, 2. Kyushu University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[3-2A]mechanical performance evaluation of micro-powder using force-displacement curve obtained from compression tests 《 Physical Property, Evaluation Technology 》
*Tao ZHANG1, Weiwei Zhou1, Naoyuki Nomura1(1. Tohoku University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[3-3A]Hot compressive deformation behavior of metallic glass composites under rapid heating condition. 《 Sintering 》
*Tatsuya Kikkawa1, Noriharu Yodoshi2, Kentaro Kudo2, Kazunari Shinagawa2(1. Graduate School of Kyushu University, 2. Kyushu University）（※This presenter is a candidate for the Student Award for Outstanding Presentation.)
[3-4B]A fast and accurate method for density measurement 《 Evaluation Technology 》
HIROFUMI SHINTOKU1, *AKIRA SHIMADA1(1. TOYOTA MOTOR CORPORATION)
155 results ( 1 - 50 )
- 1