Autumn Meeting of the Japan Society of Powder and Powder Metallurgy, 2025
Advanced Search

Session Details

Special Session: Recent Advances of Materials and Technologies on Additive Manufacturing

Recent Advances of Materials and Technologies on Additive Manufacturing

Thu. Oct 30, 2025 9:00 AM - 10:40 AM JST
Thu. Oct 30, 2025 12:00 AM - 1:40 AM UTC
Room III(HALL 3)
9:00 AM - 9:15 AM JST(12:00 AM - 12:15 AM UTC)Student Award for Outstanding Presentation candidate

[3-39A]Effect of alloy composition on the microstructure of Cu-Al alloys processed by laser rapid solidification and annealing 《 Microstructure, Control, Additive, Manufacturing 》

*Hiroki Oka1, Shaoyun Zhou1, Asuka Suzuki1, Makoto Kobashi1, Tomoharu Tokunaga1 (1. Nagoya University)
9:15 AM - 9:30 AM JST(12:15 AM - 12:30 AM UTC)Student Award for Outstanding Presentation candidate

[3-40A]Fundamental investigation of Al-Cu alloy layer fabrication technology on Cu plate by Laser Additive Manufacturing 《 Synthesis, Process, Microstructure, Control 》

*Fumihiro Ozawa1, Hiroki Oka1, Shaoyun Zhou1, Asuka Suzuki1, Makoto Kobashi1 (1. Nagoya Univ.)
9:30 AM - 9:45 AM JST(12:30 AM - 12:45 AM UTC)Student Award for Outstanding Presentation candidate

[3-41A]Effect of heat treatment on the microstructure and mechanical properties of Al–Ti alloy builds fabricated by laser powder bed fusion 《 Microstructure, Control, Additive, Manufacturing 》

*Takamune Miura1, Zhenxing Zhou1, Mingqi Dong1, Weiwei Zhou1, Naoyuki Nomura1 (1. Tohoku University Graduate School of Engineering)
9:45 AM - 10:00 AM JST(12:45 AM - 1:00 AM UTC)Student Award for Outstanding Presentation candidate

[3-42A]Microstructure and mechanical properties of hybrid second phases reinforced aluminum matrix composites prepared by additive manufacturing 《 Additive, Manufacturing 》

*Kakeru Yabe1, Li-Fu Yi1, Weiwei Zhou2, Tomoyuki Yamaguchi1, Zhenxing Zhou2, Naoyuki Nomura2, Zhong-Chun Chen1 (1. Tottori University , 2. Tohoku University)
10:00 AM - 10:15 AM JST(1:00 AM - 1:15 AM UTC)Student Award for Outstanding Presentation candidate

[3-43A]Monte Carlo simulations for liquid phase sintering behaviors of Al powder assisted by Al-Cu eutectic alloy powder 《 Sintering 》

*Ryotaro Kusunoki1, Sota Terasaka2, Asuka Suzuki1, Makoto Kobashi1 (1. Nagoya University, 2. Japan Fine Ceramics Center)
10:15 AM - 10:30 AM JST(1:15 AM - 1:30 AM UTC)

[3-44A]Changes in liquid phase distribution during non-pressure sintering of aluminum-rare earth oxide mixed powder 《 Sintering, Additive, Manufacturing 》

*Yuji Shigeta1, Yusuke Hirayama1, Keigo Kobayashi2, Zheng Liu1, Yoko Takada1, Kenta Takagi1, Jun Kato2, Kazuki Okada2 (1. National Institute of Advanced Industrial Science and Technology, 2. Mitsubishi Materials Corporation)
10:30 AM - 10:40 AM JST(1:30 AM - 1:40 AM UTC)

[Break]Break（10min）

Back to Category List